Only this week: 10% off all BOSCH power tools - discount will be deducted in the shopping cart

  • Banner image for: Banner image for:

Description

SKU: 130787
EAN: 4007220661925

Scope of Delivery:
- 1x PFERD flap disc Ø15xH10mm grit size 120

Product Description:
Resin bond - universally applicable - also suitable for machining brass, copper and zinc - shank Ø 3 mm

Technical Data:
- Shank Ø: 3mm
- Drive type: Flexible shaft drive, straight grinder
- Application recommendation: Reducing the contact pressure and peripheral speed and adding grinding oil reduces tool wear and the temperature load on the workpiece. An increase in stock removal rate should be achieved by using a coarser grit and not by increasing the contact pressure in order to prevent unnecessary tool wear and thermal stress on the workpiece. Increasing the cutting speed results in a slightly finer surface finish. Increasing the contact pressure results in a slightly coarser surface. The softer the material to be machined, the coarser the surface (when using , For best performance, use at a recommended cutting speed of 15-20 m/s). This achieves an ideal compromise between stock removal rate, surface finish, temperature load on the workpiece and tool wear. Use a suitable grinding oil for the material to significantly increase the service life and grinding performance of the tools.
- Machinable materials: Copper, aluminium, malleable cast iron, brass, cast steel, hardened, tempered steels over 1,200 N/mm² ( 54 HRC
- Machining tasks: Structuring (matting, line matting and satin finishing), levelling, fine grinding in stages, deburring, surface processing, weld seam processing
- Width: 10mm
- Note: PFERDERGONOMICS recommends flap discs in order to sustainably reduce the vibration and noise generated during use and to improve working comfort.
- Length, shaft: 40mm
- RPM, opt.: 25000RPM
- Safety instructions: For safety reasons, the specified maximum permissible speed must never be exceeded. The contact pressure must be significantly reduced if the specified optimum speed is exceeded. Safety is only guaranteed if the clamping length is at least 15 mm and the specified maximum speed is not exceeded with open shank lengths.
- Advantages: Can be used very close to edges and at angles thanks to the flat casting core design. Consistently high material removal over the entire service life, as new, aggressive abrasive is constantly released. Optimum contour adaptation due to high flexibility.

For commercial use, please observe the building regulations!

Read more

Product form

PFERD flap disc Ø15xH10mm grit size 120 ( 4000843047 )

  • Vendor PFERD
  • condition  New
  • Unzufrieden? 100 Tage kostenfreie Retoure
    €11,04
    incl. VAT, plus shipping

    in stock delivery expected in  Tue, 11/11/2025

      • American Express
      • Apple Pay
      • Google Pay
      • iDEAL
      • Klarna
      • Mastercard
      • +12 weitere

      +780.000 BROs folgen uns auf

       

      Smarte Produktberatung

      Rechnung, Versand & GPSR

      Versand & Rechnung durch: Dinotech e.K.

      Responsible Person for the EU (GPSR) EU-based economic operator that ensures the product complies with the necessary regulations.
      • info@pferd.com
      • +49226490
      • Germany
      • 51709 Marienheide
      • Hauptstr. 13
      • August Rüggeberg GmbH&Co. KG Pferd - Werkzeuge

      Description

      SKU: 130787
      EAN: 4007220661925

      Scope of Delivery:
      - 1x PFERD flap disc Ø15xH10mm grit size 120

      Product Description:
      Resin bond - universally applicable - also suitable for machining brass, copper and zinc - shank Ø 3 mm

      Technical Data:
      - Shank Ø: 3mm
      - Drive type: Flexible shaft drive, straight grinder
      - Application recommendation: Reducing the contact pressure and peripheral speed and adding grinding oil reduces tool wear and the temperature load on the workpiece. An increase in stock removal rate should be achieved by using a coarser grit and not by increasing the contact pressure in order to prevent unnecessary tool wear and thermal stress on the workpiece. Increasing the cutting speed results in a slightly finer surface finish. Increasing the contact pressure results in a slightly coarser surface. The softer the material to be machined, the coarser the surface (when using , For best performance, use at a recommended cutting speed of 15-20 m/s). This achieves an ideal compromise between stock removal rate, surface finish, temperature load on the workpiece and tool wear. Use a suitable grinding oil for the material to significantly increase the service life and grinding performance of the tools.
      - Machinable materials: Copper, aluminium, malleable cast iron, brass, cast steel, hardened, tempered steels over 1,200 N/mm² ( 54 HRC
      - Machining tasks: Structuring (matting, line matting and satin finishing), levelling, fine grinding in stages, deburring, surface processing, weld seam processing
      - Width: 10mm
      - Note: PFERDERGONOMICS recommends flap discs in order to sustainably reduce the vibration and noise generated during use and to improve working comfort.
      - Length, shaft: 40mm
      - RPM, opt.: 25000RPM
      - Safety instructions: For safety reasons, the specified maximum permissible speed must never be exceeded. The contact pressure must be significantly reduced if the specified optimum speed is exceeded. Safety is only guaranteed if the clamping length is at least 15 mm and the specified maximum speed is not exceeded with open shank lengths.
      - Advantages: Can be used very close to edges and at angles thanks to the flat casting core design. Consistently high material removal over the entire service life, as new, aggressive abrasive is constantly released. Optimum contour adaptation due to high flexibility.

      For commercial use, please observe the building regulations!

      Read more

      Recently Viewed

      Top questions at a glance

      How can I pay for my order?

      We offer a wide range of secure payment methods:

      online payment methods

      PayPal, KLARNA, Google Pay, Apple Pay and Shop Pay.

      Credit cards

      You can also pay with the major credit cards VISA, MasterCard and American Express. In this case, the payment is secured using the 3D-Secure method. If we have any reason to suspect fraudulent ordering, we will automatically cancel the payment.

      How can I pay for my order?
      How do I receive an invoice?

      You will automatically receive the invoice from our shipping partner in a separate email after receipt of payment. It will not come with the confirmation of receipt. In addition, a paper invoice will be enclosed with the order.

      Therefore, please also check your spam folder again thoroughly and otherwise get in touch here in our invoice portal.

      How do I receive an invoice?
      Returns: I want to return something

      If you wish to return all or part of your order and you're from the EU 🇪🇺, please check our returns portal.

      For returns from Switzerland 🇨🇭 and Liechtenstein 🇱🇮, use this returns portal.

      Where is my order?

      There are various ways to track the shipment status:

      The dispatch usually takes 1 - 2 working days. If it takes longer or you think the parcel has disappeared, please contact us here in our problem portal.

      Your tool family

      • <strong>Personalized support</strong>

        Personalized support

        Unlike many other platforms, we offer you personal advice and service that supports you at all times.

      • <strong></strong>

      • <strong>Best Prices</strong>

        Best Prices

        For each item with this symbol, you will currently receive the best online price (for the german market) from us. You can find the exact information on this on the product pages.

      This is Toolbrothers

      Tools are the engine of our society. Whether you're building a house, bought an IKEA cabinet or finally want to fix that leaky faucet, you need tools. We provide you with tools – and in true Toolbrothers style.
      • Super fast
      • Reliable
      • With the best service

      Log in

      Forgot your password?

      Don't have an account yet?
      Create account