Neueste Artikel
-
PFERD PFERD round brush RBU INOX Ø 40 mm wire thickness 0.2 mm ( 8000433038 )
Thu, 10/16/2025
Scope of Delivery: - Round brush RBU INOX Ø 40 mm wire thickness 0.2 mm Product Description: for cleaning, derusting, smoothing, cleaning weld seams, light deburring and removing corrosion and paint - very good corrosion resistance with optimum service life - INOX trim blue for use on all stainless steels (INOX), such as V4A. Stainless steel wire (INOX) withstands temperatures up to 450 °C - Shank Ø 6 mm Technical Data: - Drive type: Drill, straight grinder, flexible shaft drive - Application recommendation: For best performance, use a tool drive with at least 300 watts. Please observe the recommended speeds. - Mounting system: Shank - Machinable materials: Stainless steel (INOX), hard non-ferrous metal, bronze, titanium, soft titanium alloys (tensile strength 500 N/mm²), aluminium, high-temperature materials, nickel-based alloys (e.g. Inconell and Hasteloy), nickel or titanium-based superalloys, other non-ferrous metals, titanium alloys, cobalt-based alloys - Machining tasks: Rust removal, paint stripping, roughening, cleaning, deburring, removing oxide layers, removing tarnish colours - Filament material: Stainless steel wire (INOX) - Length, filament: 9mm - Ø fill material: 0.2mm - Ø shank: 6mm - RPM, opt., up to: 11700RPM - RPM, opt., from: 7200RPM - Safety instructions: When clamping the brush, ensure that the shaft is clamped as far as possible into the holder. This applies in particular to use in the high speed range. The minimum clamping length is 10 mm. - Packaging: Industrial packaging - Advantages: Optimum adaptation to the contour of the workpieces thanks to high flexibility. Very good corrosion resistance. Produces fine surfaces. - RPM, max.: 18000RPMFor commercial use, please observe the building regulations!
€16,65
-
PFERD PFERD round brush RBU 5015/6 ST 0.20 Ø 50 mm 6 mm wire thickness 0.2 mm ( 8000433016 )
Thu, 10/16/2025
Scope of Delivery: - Wheel brush RBU 5015/6 ST 0.20 Ø 50 mm 6 mm wire thickness 0.2 mm Product Description: crimped wire - can be used universally for cleaning, derusting, smoothing, cleaning weld seams, light deburring and removing corrosion and paint - shaft Ø 6 mm Technical Data: - nanFor commercial use, please observe the building regulations!
€15,53
-
PFERD PFERD round brush RBU 4009/6 ST 0.20 Ø 40 mm 6 mm wire thickness 0.2 mm ( 8000433013 )
Thu, 10/16/2025
Scope of Delivery: - Wheel brush RBU 4009/6 ST 0.20 Ø 40 mm 6 mm wire thickness 0.2 mm Product Description: crimped wire - can be used universally for cleaning, derusting, smoothing, cleaning weld seams, light deburring and removing corrosion and paint - shaft Ø 6 mm Technical Data: - nanFor commercial use, please observe the building regulations!
€13,32
-
PFERD PFERD felt polishing pen D15xH20mm 6 mm ( 8000432705 )
Scope of Delivery: - Felt polishing pin D15xH20mm 6 mm Product Description: with face hole - felt polishing points are used in conjunction with abrasive paste for pre-polishing and high-gloss polishing Technical Data: - nanFor commercial use, please observe the building regulations!
-
PFERD PFERD felt polishing pin D8xH12mm 3 mm ( 8000430523 )
Scope of Delivery: - Felt polishing pin D8xH12mm 3 mm Product Description: Felt polishing points are used in conjunction with abrasive paste for pre-polishing and high-gloss polishing Technical Data: - nanFor commercial use, please observe the building regulations!
-
PFERD PFERD felt polishing pen D10xH15mm 3 mm ( 8000430506 )
Thu, 10/16/2025
Scope of Delivery: - Felt polishing pin D10xH15mm 3 mm Product Description: Felt polishing points are used in conjunction with abrasive paste for pre-polishing and high-gloss polishing Technical Data: - nanFor commercial use, please observe the building regulations!
€11,55
-
PFERD PFERD felt polishing pen D8xH10mm 3 mm ( 8000430502 )
Scope of Delivery: - Felt polishing pin D8xH10mm 3 mm Product Description: Felt polishing points are used in conjunction with abrasive paste for pre-polishing and high-gloss polishing Technical Data: - nanFor commercial use, please observe the building regulations!
-
PFERD PFERD felt flap disc Ø 125 mm ( 8000430461 )
Thu, 10/16/2025
Scope of Delivery: - Felt flap disc Ø 125 mm Product Description: for pre-polishing and high-gloss polishing on medium to large components - due to their hardness and flexibility, they are used when geometric shapes must be precisely maintained - for use with polishing pastes - bore 22.23 mm Ø Technical Data: - Drive type: Angle grinder, cordless angle grinder - Application recommendation: Use the soft version for sanding and processing workpieces with very high contours. If very fine surfaces are to be achieved, the hard and soft versions can be used one after the other. - Version: W (soft) - Machinable materials: Nickel-based alloys (e.g. Inconell and Hasteloy), copper, aluminium, brass, bronze, hardened, tempered steels over 1,200 N/mm² (54 HRC, steels up to 1,200 N/mm² ( - Machining tasks: Polishing - Width: 22mm - Ø bore: 22.23mm - RPM, opt.: 1500RPM - Advantages: Low thermal load on the workpiece. Can be freely profiled and can therefore also be used for tools with complicated geometries. Optimum contour adaptation due to high flexibility. - RPM, max.: 7650RPMFor commercial use, please observe the building regulations!
€172,85
-
PFERD PFERD flap disc Ø80xH30mm grit size 80 ( 8000429790 )
Thu, 10/16/2025
Scope of Delivery: - Flap sander Ø80xH30mm grit size 80 Product Description: aluminium oxide A - with flaps made of abrasive on backing - for universal use from coarse to fine sanding - shaft Ø 6 mm - also suitable for processing brass, copper and zinc Technical Data: - Shank Ø: 6mm - Drive type: Flexible shaft drive, straight grinder - Application recommendation: Increasing the cutting speed results in a slightly finer surface. Increasing the contact pressure results in a slightly coarser surface. The softer the material to be processed, the coarser the surface (when using , An increase in the removal rate should be achieved by using a coarser grit size and not by increasing the contact pressure in order to prevent unnecessary tool wear and thermal stress on the workpiece. Reducing the contact pressure and peripheral speed and adding grinding oil reduces tool wear and the temperature load on the workpiece. For best performance, use at a recommended cutting speed of 15-20 m/s. This achieves an ideal compromise between stock removal rate, surface finish, temperature load on the workpiece and tool wear. Use a suitable grinding oil for the material to significantly increase the service life and grinding performance of the tools. - Machinable materials: Steels up to 1,200 N/mm² ( 54 HRC, malleable cast iron - Machining tasks: Surface processing, deburring, fine grinding in stages, structuring (matting, line matting and satin finishing), weld seam processing, levelling - Width: 30mm - Note: PFERDERGONOMICS recommends flap discs in order to sustainably reduce the vibration and noise generated during use and to improve working comfort. - Length, shaft: 40mm - RPM, opt.: 4800RPM - Safety instructions: For safety reasons, the specified maximum permissible speed must never be exceeded. The contact pressure must be significantly reduced if the specified optimum speed is exceeded. Safety is only guaranteed if the clamping length is at least 15 mm and the specified maximum speed is not exceeded with open shank lengths. - Advantages: Optimum contour adaptation due to high flexibility. Consistently high material removal rate over the entire service life, as new, aggressive abrasive is constantly released. Can be used very close to edges and at angles thanks to the flat cast core design.For commercial use, please observe the building regulations!
€15,02
-
PFERD PFERD flap disc Ø50xH30mm grit 40 ( 8000429727 )
Thu, 10/16/2025
Scope of Delivery: - Flap sander Ø50xH30mm grit 40 Product Description: aluminium oxide A - with flaps made of abrasive on backing - for universal use from coarse to fine sanding - shaft Ø 6 mm - also suitable for processing brass, copper and zinc Technical Data: - Shank Ø: 6mm - Drive type: Straight grinder, flexible shaft drive - Application recommendation: Reducing the contact pressure and peripheral speed and adding grinding oil reduces tool wear and the temperature load on the workpiece. Use grinding oil suitable for the material to significantly increase the service life and grinding performance of the tools. For best performance, use at a recommended cutting speed of 15-20 m/s. This achieves an ideal compromise between stock removal rate, surface finish, temperature load on the workpiece and tool wear. Increasing the cutting speed results in a slightly finer surface finish. Increasing the contact pressure results in a slightly coarser surface. The softer the material to be machined, the coarser the surface (when using , An increase in the stock removal rate should be achieved by using a coarser grit size and not by increasing the contact pressure in order to prevent unnecessary tool wear and thermal stress on the workpiece. - Machinable materials: Copper, hardened, tempered steels over 1,200 N/mm² ( 54 HRC - Machining tasks: Gradual fine grinding, deburring, levelling, structuring (matting, line matting and satin finishing), surface processing, weld seam processing - Width: 30mm - Note: PFERDERGONOMICS recommends flap discs in order to sustainably reduce the vibration and noise generated during use and to improve working comfort. - Length, shaft: 40mm - RPM, opt.: 7000RPM - Safety instructions: For safety reasons, the specified maximum permissible speed must never be exceeded. The contact pressure must be significantly reduced if the specified optimum speed is exceeded. Safety is only guaranteed if the clamping length is at least 15 mm and the specified maximum speed is not exceeded with open shank lengths. - Advantages: Consistently high material removal over the entire service life, as new, aggressive abrasive is constantly released. Optimum contour adaptation due to high flexibility. Can be used very close to edges and at angles thanks to the flat casting core design.For commercial use, please observe the building regulations!
€12,77
-
PFERD PFERD diamond cutting disc DG PSF Ø 230 mm bore 22.23 mm ( 8000429388 )
Scope of Delivery: - Diamond cutting disc DG PSF Ø 230 mm bore 22.23 mm Product Description: suitable for angle grinders of all power classes - abrasive: diamond D - with closed edge - high cutting quality Technical Data: - nanFor commercial use, please observe the building regulations!
-
PFERD PFERD diamond cutting disc DG PSF Ø 125 mm bore 22.23 mm ( 8000429386 )
Thu, 10/16/2025
Scope of Delivery: - Diamond cutting disc DG PSF Ø 125 mm bore 22.23 mm Product Description: suitable for angle grinders of all power classes - abrasive: diamond D - with closed edge - high cutting quality Technical Data: - nanFor commercial use, please observe the building regulations!
€27,07
I18n Error: Missing interpolation value "number1" for "You have seen {{ number1 }} out of {{ number2 }} products"